Scalloped Brick Stitch Bracelet

1. Reduce a 5 foot size of Miyuki nylon beading thread. String one Miyuki 3mm Spacer bead (SPR3), one Miyuki 2.7x12mm Twisted Bugle bead (TW2712), two SPR3 beads, one TW2712, and one SPR3. Slide the beads to the tip of the thread and go away a two foot tail.

3. Move down by way of the three beads to the suitable.

4. String one SPR3, one TW2712, and one SPR3.

5. Move down by way of the three beads to the left and up by way of the three beads to the suitable.

6. String one SPR3, one TW2712, and one SPR3. Move up by way of the three beads to the left and down by way of the three beads to the suitable.

7. Proceed in ladder sew till there are seven TW2712 beads.

8. String two Miyuki 11/0 seed beads. Move the needle below the primary thread bridge to the left to start brick stitch.

9. Move up by way of the second 11/0 and pull thread to safe.

10. String one 11/0 and go the needle below the subsequent thread bridge to the left.

11. Move up by way of the third 11/0 and pull thread to safe.

12. String one 11/0 and go the needle below the subsequent thread bridge to the left. Move up by way of the identical 11/0. String one other 11/0 and go the needle below the identical thread bridge. Proceed up by way of the identical 11/0 (this creates a rise within the row).

13. String one 11/0 and go the needle below the subsequent thread bridge to the left. Proceed up by way of the 11/0 and pull thread to safe.

14. Repeat step 12 and add two 11/0 beads onto the subsequent thread bridge.

15. Repeat step 12 and add two 11/0 beads onto the final thread bridge finishing the row. There must be ten 11/0 beads on this row.

16. String two Miyuki 10/0 Triangle beads (TR10). Skip over the primary thread bridge to the suitable and go the needle below the subsequent thread bridge.

17. Move up by way of the second TR10 bead.

18. Move down by way of the primary TR10 bead and below the corresponding thread bridge.

19. Move up by way of the primary TR10 bead.

20. Move down by way of the TR10 to the suitable and proceed below the corresponding thread bridge. Move up by way of the second TR10 and pull thread to safe.

21. Proceed in brick sew till there are 9 TR10 beads within the row (there aren’t any will increase on this row).

22. Use the 2 foot thread tail on the other facet and repeat steps 8-21 to finish this part.

23. Repeat steps 1-22 to make a second brick stitched part. Sew in and trim all remaining thread tails. These will type the 2 center parts of the bracelet.

24. Reduce a ten foot size of thread (leaving a 12 inch tail). Ladder sew 9 TR10 beads collectively.

25. Move again by way of the final two beads within the row to bolster.

26. String two 11/0 beads and go the needle below the primary thread bridge to the left. Proceed up by way of the second 11/0 and pull thread to safe.

27. Brick sew six 11/0 beads throughout the row, including one onto every corresponding thread bridge.

28. Brick sew two 11/0 beads onto the final thread bridge to extend. There will likely be ten 11/0 beads on this row.

29. String two Miyuki 8/0 seed beads. Skip over the primary thread bridge to the suitable and go the needle below the subsequent. Move up by way of the second 8/0.

30. Move down by way of the primary 8/0 and below the corresponding thread bridge, proceed up by way of the primary 8/0.

31. Move down by way of the 8/0 to the suitable and below the corresponding thread bridge, proceed up by way of the second 8/0.

32. String one 8/0, skip over the thread bridge to the suitable and go the needle below the subsequent. Move up by way of the third 8/0.

33. String one 8/0 and brick sew onto the subsequent thread bridge.

34. String one 8/0, skip over the thread bridge to the suitable and brick sew onto the subsequent thread bridge.

35. Brick sew two 8/0 beads to finish the row, including one to every corresponding thread bridge. There will likely be seven 8/0 beads on this row.

36. String two 8/0 beads.

37. Repeat steps 29-31 to safe the primary two 8/0 beads within the row.

38. Proceed in brick sew, including one 8/0 onto every of the corresponding thread bridges for a complete of six 8/0 beads on this row.

39. String one TR10, go by way of the primary loop of the 2 strand filigree clasp, and string one TR10.

40. Move the needle below second thread bridge to the suitable and proceed up by way of the second TR10.

41. Move again by way of the loop of the clasp and proceed down by way of the primary TR10. Move below the corresponding thread bridge and up by way of the primary TR10.

42. Move by way of the loop of the clasp and proceed down by way of the second TR10 and below the corresponding thread bridge. Move up by way of the second TR10. Enhance by brick stitching two TR10 beads onto the subsequent thread bridge.

43. Brick sew one TR10 onto the subsequent thread bridge. Move by way of the second loop of the clasp and brick sew one TR10 to the final thread bridge. There will likely be six TR10 beads on this row.

44. Move again by way of the clasp loop and down by way of the TR10 to the left. Proceed down by way of the rows of beads, exiting the TR10 on the suitable within the first row.

45. Repeat steps 24-44 and safe the opposite finish of the clasp to this part.

Andromeda

Celestia

Luna

Mars

Mercury

Milky Approach

Perseus

Vega